Showing 1–16 of 51 results
45 degree pipe saddle is used fro starting a 45 degree branch duct run from round pipe. This 45 degree pipe saddle is available in size for duct run from 3” to 8”. More size available upon customer request. This pipe saddle is made of 26 gauge galvanized sheet metal.
Adjustable 45 Degree elbows are are used to make turns in runs of round pipe and flexible duct from 0 (straight) to 45 degrees. They are also crimped on one end to easily fit into a pipe or duct fitting of the same diameter. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium galvanized steel. They are the fitting to use when needing to make tight corners and are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″. Ideal application with either flexible duct or sheet metal duct.
Adjustable 90 Degree elbows are are used to make turns in runs of round pipe and flexible duct from 0 (straight) to 90 degrees. They are also crimped on one end to easily fit into a pipe or duct fitting of the same diameter. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium galvanized steel. They are the fitting to use when needing to make tight corners and are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″. Ideal application with either flexible duct or sheet metal duct.
Double takeoff is used to cut into plenum or rectangular duct to begin two round duct runs. It allows transition from an air plenum or square duct to two round pipe. This double take off is available in size for starting side from 6”x6” to 12”x 12” and for ending side from 6” to 8”. This double takeoff is made of 26 gauge galvanized sheet metal.
This offset duct start collar is used for transition from plenums (duct board or lined) or a flat surface to square duct. This offset duct start collar is available in size for starting side from 8” x 10” to 20” x 10” and for ending side from 8” x 8” to 24” x 8”, and more sizes available for customer request. These offset duct start collar are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
This duct start collar is used for transition from plenums (duct board or lined) or a flat surface to square duct. This duct start collar is available in size from 8” x 8” to 24” x 10” and more sizes available for customer request. These duct start collar are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
A 90 degree end register boot is made to easily transit airflow from a round flexible or hard duct to a rectangular register or vent with a 90 degrees turn. The boot can be fastened to other ducts, including ceiling and wall units, using a nail and screw. 90 degree end register boot available in size for round inlet from 4” to 8”, for rectangular outlet from 2-1/4” x 10” to 6” x 14” and more sizes available for customer request. These boots are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
A 90 degree end stack boot is made to easily transit airflow from a round flexible or hard duct to a rectangular metal sheet stack with a 90 degrees turn. The boot can be fastened to other ducts, including ceiling and wall units, using a nail and screw. 90 degree end stack boot available in size for round inlet from 4” to 8”, for rectangular outlet from 2-1/4” x 10” to 6” x 14” and more sizes available for customer request. These boots are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
45 Degree flat elbows are used to make turns in runs of rectangular metal sheet duct. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium galvanized steel. They are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″. Ideal application with sheet metal duct.
45 Degree flat oval elbows are used to make turns in runs of oval duct. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium galvanized steel. They are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal, available for size 6”, 7” and 8”.
90 Degree flat oval elbows are used to make turns in runs of oval duct. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium galvanized steel. They are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal, available for size 6”, 7” and 8”.
45 Degree flat stack elbows are used to make turns in runs of rectangular metal sheet stacks. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium galvanized steel. They are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″. Ideal application with sheet metal stack.
90 Degree flat stack elbows are used to make turns in runs of rectangular metal sheet stacks. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium galvanized steel. They are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″. Ideal application with sheet metal stack.
Half section square duct, 2 sections to make a square duct, easy transport and easy assembly. Available size from 8” x8” to 24” x 12”, standard length 5′, more size available upon request.
This Hi-lo oval stack head with wing is used for transition from oval duct to register or grille and allow further oval duct connection, built-in wings allow for convenient attachment to wall studs. This stack head is available in size for oval duct inlet from 6” to 8”, for rectangular outlet from 10”x 4” to 14” x 6”, and more sizes available for customer request. These stack head are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
90 Degree jumper elbows are used to make turns in runs of rectangular metal sheet duct. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium galvanized steel. They are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″. Ideal application with sheet metal duct.