Showing 17–32 of 51 results
This oval stack head with wing is used for transition from oval duct to register or grille, built-in wings allow for convenient attachment to wall studs. This stack head is available in size for oval duct inlet from 6” to 8”, for rectangular outlet from 10”x 4” to 14” x 6”, and more sizes available for customer request. These stack head are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
A 90 degree oval to round elbow boot is made to easily transit airflow from a oval duct to a flexible or metal sheet round duct or round diffuser with a 90 degrees turn. The boot can be fastened to other ducts, including ceiling and wall units, using a nail and screw. 90 degree oval to round elbow boot available in size for oval inlet from 6” to 8”, for round outlet from 6” to 8”and more sizes available for customer request. These boots are made of 26 gauge galvanized sheet metal up to 12″.
A 90 degree oval to round end boot is made to easily transit airflow from a oval duct to a flexible or metal sheet round duct or round diffuser with a 90 degrees turn. The boot can be fastened to other ducts, including ceiling and wall units, using a nail and screw. 90 degree oval to round end boot available in size for oval inlet from 6” to 8”, for round outlet from 6” to 8”and more sizes available for customer request. These boots are made of 26 gauge galvanized sheet metal up to 12″.
A 90 degree register boot is made to easily transit airflow from a round flexible or hard duct to a rectangular register or vent with a 90 degrees turn. The boot can be fastened to other ducts, including ceiling and wall units, using a nail and screw. 90 degree register boot available in size for round inlet from 4” to 8”, for rectangular outlet from 2-1/4” x 10” to 6” x 14” and more sizes available for customer request. These boots are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
A 90 degree register boot with 17” plate is made to easily transit airflow from a round flexible or hard duct to a rectangular register or vent with a 90 degrees turn. The boot can be fastened to other ducts, including ceiling and wall units, using a nail and screw. 90 degree register boot available in size for round inlet from 6” to 8”, for rectangular outlet from 8” x 8” to 4” x 12” and more sizes available for customer request. These boots are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
Round duct transition is used to connect round duct in different size. It is available in size for starting end from 4” to 18”and for ending size from 3” to 16”. More size available for customer request. The round duct transition is made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
Round duct tee is used for starting branch duct run from round pipes. This round duct tee is available in size for duct run from 3” to 8”, and for duct branch from 3” to 8”. More size available upon customer request. This round duct tee is made of 26 gauge galvanized sheet metal.
Round end cap is used to seal the end of round duct, It is available in size from 3” to 20”, and more sizes available for customer request. This round end cap is made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
This round start collar is for transition from flat surface to round pipe or insulated flex duct. It is available in size from 3” to 20”, and it is made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
This round start collar with damper is for transition from flat surface to round pipe or insulated flex duct with damper for flow control. It is available in size from 3” to 20”, and it is made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
Side takeoff is used to cut into plenum or rectangular duct to begin a trunk line or branch-like runs. It allows transition from an air plenum or square duct to a round pipe. This side take off is available in size for starting side from 6”x6” to 12”x 12” and for ending side from 6” to 8”. This side takeoff is made of 26 gauge galvanized sheet metal.
Oval metal duct with snap-lock design. Available in size from 9” to 24”, standard length 5′, more size available for customer request. Oval is made of 24 gauge galvanized sheet metal.
Round metal duct with snap-lock design. Available in diameter from 3” to 8”, standard length 5′, made of 26 gauge galvanized sheet metal.
This spin-in round start collar is for transition from flat surface to round pipe or insulated flex duct. Spin-in designed for easy installation. It is available in size from 3” to 20”, and it is made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
This spin-in round start collar with damper is for transition from flat surface to round pipe or insulated flex duct with damper for flow control. Spin-in designed for easy installation. It is available in size from 3” to 20”, and it is made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
Spiral pipe, spiral design for extra strength, available diameter from 4” to 63”, length 10′, the sprial pipe is made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.