Square duct end cap is used to seal the end of square duct. It is available in size from 8” x 8” to 24” x 12”, and more sizes available for customer request. This square duct end cap is made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
Square duct transition is used to connect square duct in different size. It is available in size for starting end from 10” x 8” to 24” x 10” and for ending size from 8”x 8” to 20” x 10”. More size available for customer request. The square duct transition is made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
A 90 degree stack boot is made to easily transit airflow from a round flexible or hard duct to a rectangular metal sheet stack with a 90 degrees turn. The boot can be fastened to other ducts, including ceiling and wall units, using a nail and screw. 90 degree stack boot available in size for round inlet from 4” to 8”, for rectangular outlet from 2-1/4” x 10” to 6” x 14” and more sizes available for customer request. These boots are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
Stack end cap is used to seal the end of wall stack. It is available in size from 2-1/4” x 10” to 3-1/4” x 14”, and more sizes available for customer request. This stack end cap is made of 26 gauge galvanized sheet metal.
This stack head with wing is used for transition from rectangular stack duct to register or grille, built-in wings allow for convenient attachment to wall studs. This stack head is available in size for stack inlet from 10” x 3-1/4” to 14” x 3-1/4”, for rectangular outlet from 10”x 6” to 14” x 6”, and more sizes available for customer request. These stack head are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
This stack start collar is used for transition from plenums (duct board or lined) or a flat surface to square stack. This stack start collar is available in size from 2-1/4” x 12” to 3-1/4” x 14” and more sizes available for customer request. These stack start collar are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
A straight register boot is made to easily transit airflow from a round flexible or hard duct to a rectangular register or vent. The boot can be fastened to other ducts, including ceiling and wall units, using a nail and screw. Straight register boot available in size for round inlet from 4” to 8”, for rectangular out let from 2-1/4” x 10” to 6” x 14” and more sizes available for customer request. These boots are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
A straight register boot with 17” plate is made to easily transit airflow from a round flexible or hard duct to a rectangular register or vent. The boot can be fastened to other ducts, including ceiling and wall units, using a nail and screw. Straight register boot available in size for round inlet from 6” to 8”, for rectangular outlet from 8” x 8” to 4” x 12” and more sizes available for customer request. These boots are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
A straight stack boot is made to easily transit airflow from a round flexible or hard duct to a rectangular metal sheet stack. The boot can be fastened to other ducts, including ceiling and wall units, using a nail and screw. Straight stack boot available in size for round inlet from 4” to 8”, for rectangular out let from 2-1/4” x 10” to 6” x 14” and more sizes available for customer request. These boots are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
Top takeoff is used to cut into plenum or rectangular duct to begin a trunk line or branch-like runs. It allows transition from an air plenum or square duct to a round pipe. This top take off is available in size for starting side from 6”x6” to 12”x 12” and for ending side from 6” to 8”. This top takeoff is made of 26 gauge galvanized sheet metal.
This transition takeoff is used for transition from plenums (duct board or lined) or a flat surface to square stack duct. This transition takeoff is available in size for starting side from 14” x 8” to 30” x 8′ and for ending side from 14” x 8” to 30” x 8”, and more sizes available for customer request. These transition takeoffs are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″.
45 Degree vertical elbows are used to make turns in runs of rectangular metal sheet duct. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium galvanized steel. They are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″. Ideal application with sheet metal duct.
90 Degree vertical elbows are used to make turns in runs of rectangular metal sheet duct. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium galvanized steel. They are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″. Ideal application with sheet metal duct.
90 Degree vertical elbows are used to make turns in runs of rectangular metal sheet duct. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium galvanized steel. They are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″. Ideal application with sheet metal duct.
45 Degree vertical oval elbows are used to make turns in runs of oval duct. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium galvanized steel. They are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal, available for size 6”, 7” and 8”.
90 Degree vertical oval elbows are used to make turns in runs of oval duct. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium galvanized steel. They are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal, available for size 6”, 7” and 8”.